Elantr's Hyundai
+ Petrol engines 1,6, 1,8 and 2,0 of l
+ Diesel engine of 2,0 l
+ greasing System
+ cooling System
+ Fuel system
+ Monitoring systems and decrease in toxicity of the fulfilled gases
+ ignition System
+ System of preliminary heating of the diesel engine
+ Coupling
+ Mechanical transmission
+ Automatic transmission
+ Power shafts, forward and back axes
+ Suspension bracket
+ Steering
+ Brake system
+ Body
+ air Central air
- Electric equipment
Specifications
Charging system
Generator
Power failure check on a wire connecting the storage battery to the generator
Check of the current developed by the generator
Check of developed tension
Generator of petrol engines
Generator of the diesel engine
Storage battery
Start system
Starter of petrol engines
Starter of the diesel engine
Safety locks
Block of safety locks
Multipurpose switch
Sound signal
Combination of devices
Switch of position of the parking brake
Screen wiper and stekloomyvatel of a windscreen
Screen wiper of back glass
Headlights and forward indexes of turn
Forward fog lights and turn repeaters
The back combined lamp
Top stoplight
Lamp of illumination of registration plate
The ceiling lamp (with the hatch)
The ceiling lamp (without the hatch)
Lamp of illumination of salon
Check of the relay of headlights
Radio receiver
Heater of back glass
Safety cushions (SRS)
Seat belts
Search and elimination of malfunctions
Specification for adjustments and control
Electric circuits
|
Starter of the diesel engine
Sequence of dismantling of a starter
|
|
Assembly of a starter is carried out in sequence, return dismantling. |
Adjustment of a gap of a gear wheel
|
|
Disconnect a wire of the engine of a starter from the plug "M".
|
|
Additional wires connect plugs of the storage battery to plugs S and M.
|
|
|
The following check is necessary for executing during 10 with as the coil of the traction relay, otherwise, can fuse. |
|
|
Include ignition, thus a gear wheel of a starter it will be pushed forward. A finger remove a gear wheel back and shchupy check a gap between a gear wheel and a stopper.
|
If the gap differs from demanded, adjust it, adding or cleaning laying between the traction relay and a forward cover. Gear wheel gap: 0,5–0,2 mm.
|
|
Check of the traction relay of a starter
|
|
Disconnect a wire of the engine of a starter from the plug "M". The traction relay is serviceable, if the plunzher is involved at connection of plugs of the storage battery to S and M plugs. If the gear wheel is not put forward, replace the traction relay.
|
|
|
This check is necessary for executing during 10 with as the coil of the traction relay, otherwise, can fuse. |
Check of a holding winding of the traction relay
|
|
Disconnect a wire of the engine of a starter from the plug "M". Additional wires connect plugs of the storage battery to the plug "S" and the case of the traction relay and manually to a stopper extend a gear wheel. If the gear wheel remains in this situation, means, the holding winding of the traction relay is serviceable.
|
|
|
This check is necessary for executing during 10 with as the coil of the traction relay, otherwise, can fuse.
|
Check of return of a plunzher of the traction relay
|
|
Disconnect a wire of the engine of a starter from the plug "M". Additional wires connect plugs of the storage battery to the plug "M" and the case of the traction relay, thus the gear wheel of a starter should be pushed forward. After a detachment of wires the gear wheel of a starter should return to a starting position quickly.
|
|
|
This check is necessary for executing during 10 with as the coil of the traction relay, otherwise, can fuse.
|
Operational tests (idling)
|
|
|
|
For carrying out tests of idling collect the scheme shown in drawing.
|
Establish a rheostat cursor in such situation at which the voltmeter will show tension 11,5 In, thus check a current consumed by a starter and be convinced that the shaft of a starter is turned easily and smoothly. If the consumed current differs from demanded, by the table determine and eliminate a cause of defect.
|
Sign
|
Possible reason
|
|
Big consumed current with low frequency of rotation of a shaft of a starter
|
The polluted bearing |
| Friction of a winding of a rotor about a pole |
| The winding of a rotor and the coil of excitement are closed on "weight" |
| The rotor winding is damaged |
|
Big consumed current in the absence of rotation of a shaft of a starter
|
The solenoidal switch is closed on "weight" |
| The winding of a rotor and the coil of excitement are closed on "weight" |
| The bearing is jammed |
|
There is no consumed current and a shaft of a starter does not rotate
|
Damage of a rotor and excitement coil |
| The brush is broken or the flexible conductor of a brush is torn off |
| Contact between a brush and a collector is broken |
|
Small consumed current with low frequency of rotation of a shaft of a starter
|
Wrong connection of a winding of the coil of excitement |
|
Big consumed current at high frequency of rotation of a shaft of a starter
|
Short circuit in the excitement coil |
|
|
|
|