Elantr's Hyundai
+ Petrol engines 1,6, 1,8 and 2,0 of l
+ Diesel engine of 2,0 l
+ greasing System
+ cooling System
+ Fuel system
+ Monitoring systems and decrease in toxicity of the fulfilled gases
+ ignition System
+ System of preliminary heating of the diesel engine
+ Coupling
+ Mechanical transmission
+ Automatic transmission
+ Power shafts, forward and back axes
+ Suspension bracket
+ Steering
+ Brake system
+ Body
+ air Central air
- Electric equipment
Specifications
Charging system
Generator
Power failure check on a wire connecting the storage battery to the generator
Check of the current developed by the generator
Check of developed tension
Generator of petrol engines
Generator of the diesel engine
Storage battery
Start system
Starter of petrol engines
Starter of the diesel engine
Safety locks
Block of safety locks
Multipurpose switch
Sound signal
Combination of devices
Switch of position of the parking brake
Screen wiper and stekloomyvatel of a windscreen
Screen wiper of back glass
Headlights and forward indexes of turn
Forward fog lights and turn repeaters
The back combined lamp
Top stoplight
Lamp of illumination of registration plate
The ceiling lamp (with the hatch)
The ceiling lamp (without the hatch)
Lamp of illumination of salon
Check of the relay of headlights
Radio receiver
Heater of back glass
Safety cushions (SRS)
Seat belts
Search and elimination of malfunctions
Specification for adjustments and control
Electric circuits
|
Starter of petrol engines
Removal and installation
|
|
Disconnect a wire from the negative plug of the storage battery.
Disconnect a cable of a drive of a speedometer and gear shifting.
Disconnect from a starter the socket and a wire from the plug.
Turn out bolts and remove a starter.
Installation is carried out to sequences, return to removal.
|
|
Check and replacement of elements of a stator
Adjustment of a gap of a gear wheel
|
|
Disconnect a wire of the engine of a starter from the plug "M".
|
|
Additional wires connect plugs of the storage battery to S and M plugs.
|
Include ignition, thus a gear wheel of a starter it will be pushed forward.
|
|
This check is necessary for executing during 10 with as, otherwise, can fuse the solenoid of the traction relay. |
|
|
Shchup check a gap between a gear wheel and a stopper. If the gap differs from demanded, adjust it, adding or cleaning laying between the traction relay and a forward cover. Gear wheel gap: 0,5–0,2 mm.
|
|
|
Check of the traction relay of a starter
|
|
Disconnect a wire of the engine of a starter from the plug "M".
|
|
Additional wires connect plugs of the storage battery to S and M plugs.
|
Include ignition, thus a gear wheel of a starter it will be pushed forward. If the gear wheel is not put forward, replace the traction relay.
|
|
|
|
This check is necessary for executing during 10 with as the coil of the traction relay, otherwise, can fuse. |
Check of a holding winding of the traction relay
|
|
|
|
Disconnect a wire of the engine of a starter from the plug "M".
Additional wires connect plugs of the storage battery to the plug "S" and the case of the traction relay.
|
|
|
This check is necessary for executing during 10 with as the coil of the traction relay, otherwise, can fuse.
|
If the gear wheel remains on a place, means, the holding winding of the traction relay is damaged and, it is necessary to replace the traction relay.
|
|
Check of return of a plunzher of the traction relay
|
|
Disconnect a wire of the engine of a starter from the plug "M".
Additional wires connect plugs of the storage battery to the plug M and the case of the traction relay.
|
|
This check is necessary for executing during 10 with as the coil of the traction relay, otherwise, can fuse. |
|
|
The gear wheel of a starter should be pushed forward. After a detachment of wires the starter gear wheel quickly should return to a starting position.
|
|
|
Operational tests (idling)
|
|
|
|
For carrying out tests of idling collect the scheme shown in drawing.
|
Establish a rheostat cursor in such situation at which the voltmeter will show tension 11,5 In, thus check a current consumed by a starter, and be convinced that the shaft of a starter is turned easily and smoothly. Current: no more than 60 And.
|
|
Gear wheel with the obgonny coupling
To remove the obgonny coupling from a rotor shaft, it is necessary to remove a persistent ring previously.
|
|
Move a persistent ring to a gear wheel and remove a spring ring. Now the persistent ring can be removed from a shaft.
|
Check of a winding of a rotor
|
|
|
|
Ohmmeter check conductivity between a collector and a rotor. In the presence of conductivity replace a rotor.
|
|
|
In the special device check a rotor winding. In the presence of short circuits replace a rotor. If the steel strip attached to a rotor, vibrates, means, in windings of a rotor there are short circuits.
|
|
|
Ohmmeter check conductivity between collector segments. In the absence of conductivity replace a rotor.
|
|
|
Check of coils of a stator
|
|
|
|
Ohmmeter check conductivity of coils of a stator. In the absence of conductivity replace stator coils.
|
|
|
With the coil established in the case, check conductivity between a conclusion of the coil and the starter case. In the presence of conductivity replace stator coils.
|
|
|
Check of brushes
|
|
If the brush is worn-out to the designated limit, replace it.
|
Check of a shchetkoderzhatel
|
|
Ohmmeter check conductivity between each isolated brush and a plate. In the presence of conductivity replace a shchetkoderzhatel.
|
Check of the obgonny coupling
|
|
Check a condition of teeths of a gear wheel of the obgonny coupling and, in the presence of damages, replace it. Also check a condition of teeths of a gear wreath of a flywheel.
|
|
Turn a gear wheel. The gear wheel should be turned freely clockwise and be blocked at a provorachivaniye counter-clockwise
|
|
|
Replacement of brushes
|
|
Remove a worn-out brush, thus be careful not to damage a wattled wire.
Emery paper smooth out the end of a wattled occasion to provide reliable contact it with a new brush.
|
|
Replacement of the back plug
|
|
Before to remove the plug, it is necessary to measure depth of its installation.
|
|
The plug can be removed by means of a stripper, as is shown in drawing.
|
Establish the new plug on previously measured depth.
|
|
Starter assembly
|
|
Establish the obgonny coupling for the forward end of a shaft of a rotor.
|
|
Establish a persistent ring and a spring ring from the forward party of a shaft of a rotor then move a persistent ring completely to a spring ring.
|
|
|
At lever installation in a forward cover pay attention to its situation. If the lever to establish on the contrary, the gear wheel will be put constantly forward outside and cannot work properly.
|
|
|
Switch of blocking of ignition
|
|
Check that the installation height, a free wheeling and a pin gap with a head and an opening under шплинт pedals of coupling are in normal limits.
|
Check of the relay of a starter
|
|
Remove the relay of a starter and check conductivity between its plugs. If conductivity does not correspond demanded, replace the relay.
|
Check of the switch of blocking of ignition
|
|
Check conductivity between plugs of the switch of blocking of ignition.
|
|
|