Hyundai Elantra

since 2000-2004 of release

Repair and car operation



Elantr's Hyundai
+ Petrol engines 1,6, 1,8 and 2,0 of l
+ Diesel engine of 2,0 l
+ greasing System
+ cooling System
+ Fuel system
+ Monitoring systems and decrease in toxicity of the fulfilled gases
+ ignition System
+ System of preliminary heating of the diesel engine
+ Coupling
+ Mechanical transmission
- Automatic transmission
   Specifications
   Check of level of liquid in an automatic transmission
   Liquid replacement in an automatic transmission
   Check of conductivity of the switch of ranges of a transmission (F4A42)
   Switch of ranges of a transmission and adjustment of a cable of management (F4A42)
   Check of operation of the lever of the selector (A4AF3)
   Adjustment of the switch of indication of position of the lever of the selector (A4AF3)
   Check of components of an automatic transmission (F4A42)
   Testing of collaboration of an automatic transmission and the engine on the motionless car (F4A42)
   Check of pressure of transmission liquid (F4A42)
   Check of pressure of transmission liquid (А4AF3)
   Diagnostics function
   Diagnostic codes
   Adjustment of an axial gap of a reactionary brake (F4A42)
   Adjustment of an axial gap of a brake of the second transfer (F4A42)
   Adjustment of an axial gap of a brake of low transfer and transfer of a backing (F4A42)
   Adjustment of an axial gap of a solar gear wheel of lowering transfer (F4A42)
   Adjustment of preliminary loading of differential (F4A42)
   Elements of system of hydraulic management
   Identification of bearings of an automatic transmission of F4A42
   Control lamp of malfunctions (MIL)
   Identification of bearings of an automatic transmission of F4A43
   Adjustment of the servo-driver of compulsory inclusion of a low gear (А4АF3)
   Pressure adjustment in the highway (А4АF3)
   Replacement of an oil sealing ring of a power shaft
   Removal and installation of a transmission of F4A42
   Removal and installation of a transmission of A4AF3
   Management of an automatic transmission
   Interlock installation
   Installation of the device of blocking of a key
+ Power shafts, forward and back axes
+ Suspension bracket
+ Steering
+ Brake system
+ Body
+ air Central air
+ Electric equipment
Electric circuits



Removal and installation of a transmission of F4A42

Removal

 PERFORMANCE ORDER

    Disconnect, first of all, a wire from the negative plug of the storage battery, then – from positive. Remove the storage battery and a battery support.
    Turn out a drain stopper and merge in suitable capacity transmission oil from a transmission.
    Remove the air filter. Disconnect the socket from the speedometer sensor.
    Disconnect the socket from the switch of ranges of a transmission, the solenoidal socket and the socket from the sensor of temperature of oil.
    Disconnect a hose from an oil radiator.
    Remove a management cable.
    Disconnect the kardanny hinge of a shaft of a steering column from steering transfer.

Note position of the kardanny hinge of a shaft of a steering column and a shaft of steering transfer.

    Disconnect a hose from the pump of the amplifier of a steering.
    Disconnect a returnable hose from the oil pump of the amplifier of a steering.
    Turn out the top bolts of fastening of a transmission.
    The special adaptation J28467-B, J28467-125 support the engine so that the weight of the engine was perceived by the adaptation.
    Remove forward wheels and supports of forward brakes.
    Disconnect from a rotary fist the spherical hinge of a tip of steering draft.
    Remove the sensor of speed and turn out bolts of fastening of a forward rack to a rotary fist.
    Remove a transmission arm.
      Turn out a bolt of fastening of a support.

b. Turn out (top) bolt from a body.

c. Turn out (lateral) bolt from a body.

d. Turn out a lateral assembly bolt of fastening of a transmission.

    Remove a forward roller stopper.
      Turn out a bolt of fastening of a support.

b. Turn out (top) bolt of fastening of a stopper.

c. Turn out (bottom) bolt of fastening of a stopper.

    Remove a back roller stopper.
      Turn out a bolt of fastening of a support.

b. Turn out a bolt of fastening of a stopper.

    Remove a power shaft.
    Turn out bolts and remove the bottom frame.
    Support a transmission a jack.
    Turn out the bottom bolts of fastening of a transmission.
    Turn out bolts of fastening of a transmission to the engine. Remove a transmission from the car.

  1. Support of the engine and transmission should be established on the places without preliminary tension.
  2. Sequence of installation of arms.
    1) Arm of installation of the engine.
    2) Top arm of a transmission.
    3) Arm of a back support.
    4) Arm of a forward support.
  3. At installation of an arm of a forward support be careful not to damage a support that can lead to the increased vibration.

Installation

 PERFORMANCE ORDER

    Establish on a forward part of a transmission the hydrotransformer and establish a transmission to the engine.

If the hydrotransformer to establish at first on the engine, at installation of a transmission the sealing ring of a transmission can be damaged.

    Establish a cable of management of a transmission and adjust as follows.
      Move the lever of the selector and the switch of ranges of a transmission to situation N and establish a cable of management of a transmission. At connection of a cable of management to establishing arm of a transmission, establish a clip so that it contacted with a management cable. As adjusting nut choose any free wheeling in a cable of management and check that the lever of the selector moves smoothly. Check that the cable of management is adjusted correctly.
    Installation is carried out to sequences of return to removal.