Hyundai Elantra

since 2000-2004 of release

Repair and car operation



Elantr's Hyundai
+ Petrol engines 1,6, 1,8 and 2,0 of l
+ Diesel engine of 2,0 l
+ greasing System
+ cooling System
+ Fuel system
+ Monitoring systems and decrease in toxicity of the fulfilled gases
+ ignition System
+ System of preliminary heating of the diesel engine
+ Coupling
+ Mechanical transmission
+ Automatic transmission
+ Power shafts, forward and back axes
+ Suspension bracket
+ Steering
- Brake system
   Specifications
   Check of the vacuum amplifier of brakes
   Check of the unilateral vacuum valve
   Pumping of hydraulic system of a drive of brakes
   Adjustment of a course of the parking brake
   Brake pedal
   Vacuum amplifier of brakes
   Main brake cylinder
   Replacement of forward brake shoes
   Support of a forward brake
   Back disk brakes
   Back drum-type brakes
   Replacement of the working brake cylinder
   Pressure regulator
   Brake tubes and hoses
   Parking brake
   Anti-blocking system of brakes (ABS)
   Hydraulic HECU block
   Sensor of frequency of rotation of a wheel
   Pumping of hydraulic system of a drive of brakes with scanner use
   Search and elimination of malfunctions
+ Body
+ air Central air
+ Electric equipment
Electric circuits



Main brake cylinder

Removal

 PERFORMANCE ORDER

  1. Disconnect the electric socket from the sensor of level of brake liquid.
  2. Disconnect tubes of brake system from the main brake cylinder and close the opened openings suitable jams.

Brake liquid dissolves paint, plastic and isolation of wires therefore at casual hit of liquid on a paint and varnish covering of the car or its components wash out them a large amount of water.

  1. Unscrew nuts of fastening of the main brake cylinder and remove the main brake cylinder. Inhaling moment: 8–12 N • m.

Dismantling

 PERFORMANCE ORDER

  1. Remove a stopper and merge from a tank brake liquid.
  1. Turn out screws and, using a screw-driver as the lever, remove a tank from the main brake cylinder.
  1. Remove a lock ring.
  1. Screw-driver press the primary piston, get a cylindrical pin and remove the primary piston.
  1. Screw-driver press the secondary piston, get a cylindrical pin and remove the secondary piston.

Do not assort primary and secondary pistons.

Check

 PERFORMANCE ORDER

  1. Check an internal surface of the case of the main brake cylinder on lack of a rust and development.
  2. Check the main brake cylinder on lack of wear or damages. If necessary clear or replace the main brake cylinder.
  1. If the opening of the case of the main brake cylinder is damaged, replace the main brake cylinder assembled.
  2. For removal of pollution clear the case of the main brake cylinder isopropyl alcohol.

Assembly

 PERFORMANCE ORDER

  1. Grease with the recommended brake liquid an internal surface of the main brake cylinder and external surfaces of primary and secondary pistons.
  1. Accurately insert two springs and pistons into an opening of the main brake cylinder.
  1. Press pistons and establish holding ring.
  1. Screw-driver press the piston and establish a cylindrical pin.
  2. Establish two condensing rings.
  1. With effort insert a tank into condensing rings of the main brake cylinder.

Installation

 PERFORMANCE ORDER

  1. Establish the main brake cylinder on the vacuum amplifier of brakes.
  2. Establish the main brake cylinder and the vacuum amplifier of brakes on a partition of a motor compartment.
  3. Connect brake tubes to the main brake cylinder.
  4. Attach a vacuum hose to the vacuum amplifier of brakes.
  5. Connect draft to a pedal of a brake and establish a pin with a head and an opening under шплинт and fix its new spring the shplinty.
  6. Fill in brake liquid and remove air from a hydraulic contour of brake system.

Do not try to repair the vacuum amplifier of brakes, as it not folding type.