Elantr's Hyundai
+ Petrol engines 1,6, 1,8 and 2,0 of l
- Diesel engine of 2,0 l
Specifications
Compression check
Adjustment of a tension of a gear belt
Gear belt
Cover of a head of cylinders and stopper
Camshaft
Balancing shaft
Repair of a head of cylinders
Engine support
Elements of support which are subject to check
Block of cylinders
Removal and engine and transmission installation
Cranked shaft
Piston
Turbokompressor
Cooler of inflated air
Air filter (ACL)
System of production of the fulfilled gases
Search and elimination of malfunctions
+ greasing System
+ cooling System
+ Fuel system
+ Monitoring systems and decrease in toxicity of the fulfilled gases
+ ignition System
+ System of preliminary heating of the diesel engine
+ Coupling
+ Mechanical transmission
+ Automatic transmission
+ Power shafts, forward and back axes
+ Suspension bracket
+ Steering
+ Brake system
+ Body
+ air Central air
+ Electric equipment
Electric circuits
|
Gear belt
Removal
|
|
Turn a cranked shaft clockwise and combine adjusting labels that the piston in the first cylinder was established in the top dead point in a compression step. At this time adjusting labels of a pulley of a camshaft and a cover of a head of the block of cylinders should be combined, and the adjusting pin of a pulley of a camshaft should be above. |
|
|
Remove poliklinovy a belt and a pulley of a cranked shaft.
Remove a casing of a gear belt.
Remove an arm of a support of the engine.
|
|
For a head of a big bolt turn the mechanism of a tension of a gear belt before combination of a basic plate with an opening in a casing, then insert a clamp into an opening.
|
|
|
Six-sided key weaken fixing bolt.
|
|
|
For a head of a big bolt turn the mechanism of a tension of a gear belt against the stop clockwise.
|
|
|
Tighten fixing bolt.
|
Remove a gear belt.
|
|
Note the direction of rotation of a gear belt for repeated installation it in initial situation. |
|
|
Turn out a sharnirny bolt and remove the mechanism of an automatic tension of a gear belt.
|
|
|
Check
Pulleys, pulley of the mechanism of a tension of a gear belt and single pulley
|
|
. Check pulleys of distributive and cranked shaft, a pulley of the mechanism of a tension and a single pulley on lack of non-uniform wear, cracks and damages. Replace them as required.
Check ease and smoothness of rotation of a pulley of the mechanism of a tension and a single pulley, and also absence of extraneous noise at rotation. Replace them as required.
|
|
Replace pulleys if there is a leakage of lubricant.
|
|
|
Mechanism of an automatic tension of a gear belt
|
|
Check the mechanism of an automatic tension of a gear belt on absence of leaks and, if necessary, replace it.
|
|
Check a tip on lack of wear or damages and, if necessary, replace it.
|
|
|
Gear belt
|
|
Check a gear belt on lack of traces of oil, water or a dust. If it is necessary replace a belt. Insignificant traces should be wiped by a dry fabric or paper. Do not clean a gear belt solvent.
After engine or adjustment repair a belt tension, check a belt condition. In the presence of the following defects, replace a gear belt.
|
|
Installation
|
|
Establish a pulley of a cranked shaft on a cranked shaft.
|
|
Special attention turn on the direction of installation of a flange. If the pulley is established incorrectly, it will lead to damage of a gear belt. |
Establish a special washer and screw a bolt of fastening of a pulley to a cranked shaft and then tighten a bolt. Inhaling moment: 185–195 N • m.
|
|
Gear belt
|
|
Check the provision of adjusting labels.
from a cranked shaft: an adjusting label on a pulley of a cranked shaft and a rod for installation of the moment of injection;
from a camshaft: an adjusting label on a pulley of a camshaft and a head of cylinders.
Establish the tension mechanism.
Establish the mechanism of an automatic tension of a gear belt.
|
|
Tighten a sharnirny bolt. Inhaling moment: 50-55H • m.
|
Establish a gear belt.
|
Description
|
Defect
|
| 1. Rigid return surface of a gear belt |
|
|
The surface has a glossy appearance. Rigidity of a surface such is that a nail does not leave traces on a belt
|
|
| 2. Cracks on a return surface of a gear belt |
|
| 3. Cracks or stratification of a gear belt |
|
| 4. Strongly worn-out teeths |
|
|
The tooth party is worn-out, fibers, a cord and the rubber basis become thus visible
|
|
| 5. Strongly worn-out teeths (the last stage) |
|
|
The tooth party is worn-out, attritions become thus visible and the thickness of tooth is reduced
|
|
| 6. Cracks in the basis of teeths |
|
| 7. Lack of tooth |
|
| 8. Strong wear of one party of a belt |
|
|
The normal belt should have an equal lateral end face, as though cut off by a sharp knife
|
|
| 9. Cracks on lateral face of a gear belt |
|
Weaken fixing bolt, the lever of the mechanism of a tension thus will move and will automatically pull a gear belt.
|
|
Turn clockwise a cranked shaft of the engine on two turns and check combination of adjusting labels.
|
Tighten fixing bolt.
Remove a clamp.
|
|
|
|