Hyundai Elantra

since 2000-2004 of release

Repair and car operation



Elantr's Hyundai
+ Petrol engines 1,6, 1,8 and 2,0 of l
+ Diesel engine of 2,0 l
+ greasing System
+ cooling System
+ Fuel system
+ Monitoring systems and decrease in toxicity of the fulfilled gases
+ ignition System
+ System of preliminary heating of the diesel engine
+ Coupling
+ Mechanical transmission
+ Automatic transmission
+ Power shafts, forward and back axes
+ Suspension bracket
- Steering
   Specifications
   Check of a free wheeling of a steering wheel
   Check of an angle of rotation of forward wheels
   Check of a torque of a pin of the spherical hinge of a tip of steering draft
   Check of effort of turn of a steering wheel
   Check of return of a steering wheel in a starting position
   Check of a tension of a belt of a drive of the pump of the power steering
   Check of level of liquid
   Liquid replacement in a hydraulic drive of the power steering
   Pumping of hydraulic system of the amplifier of a steering
   Check of pressure of liquid in hydraulic system
   Steering column/helmsman shaft
   Removal and installation of the lock of a steering column
   Steering transfer
   Hoses of the amplifier of a steering
   Filling with liquid of the mechanism of the amplifier of a steering
   Pump of the amplifier of a steering
   Search and elimination of malfunctions of a steering
+ Brake system
+ Body
+ air Central air
+ Electric equipment
Electric circuits



Pump of the amplifier of a steering

Removal

 PERFORMANCE ORDER

  1. Disconnect a pressure head hose from the pump.
  1. Disconnect soaking-up filter from the socket of absorption and merge liquid in the container.
  1. Weaken bolts of fastening of the pump and remove a driving belt.
  1. Turn out a bolt of adjustment of a tension of a belt.
  1. Remove a driving belt from a pulley of the pump of the amplifier of a steering.
  1. Turn out bolts of fastening of the pump and a bolt of adjustment of a tension of a belt.
  1. Remove the pump of the amplifier of a steering.

Be careful, as liquid will follow from the pump.

  1. Remove an arm of the pump of the amplifier of a steering.

Dismantling

 PERFORMANCE ORDER

  1. Remove from the pump soaking-up pipe and a sealing ring.
  1. Turn out four bolts and remove a back cover with laying and pins.
  2. Remove a statorny ring.
  3. Remove a rotor and blades.
  4. Remove a forward lateral plate.
  5. Remove internal and external sealing rings.
  6. Remove a spring.

At assembly it is necessary to use new laying and a sealing ring.

  1. Fix a pulley in a vice, unscrew a nut of fastening of a pulley and remove a spring washer.
  1. Remove a pulley and a segment shponka.
  1. Using special flat-nose pliers, remove a lock ring and the rasporny plug.
  1. Squeeze out a pulley shaft with the bearing. If necessary use a kapron hammer.
  1. Remove a sealing ring from the pump case.

At assembly it is necessary to use a new sealing ring.

  1. Disconnect the socket from the case of the oil pump and remove the valve and a spring.
  2. Remove from a connector a sealing ring.

Do not make dismantling of the control valve.

Check

 PERFORMANCE ORDER

  1. Measure length of a spring of the control valve in a free condition. Length of a spring in a free condition: 36,5 mm.
  2. Be convinced that the control valve will not bend.
  3. Check a shaft on lack of wear and damages.
  4. Check a driving belt on lack of wear and loss of properties.
  5. Check rotor and blade grooves on lack of wear.
  6. Check a contact surface of a statorny ring and blades on lack of wear.
  7. Check blades on absence of damages.
  8. Check on lack of wear a lateral plate and a surface of contact of a shaft and a pump cover.

Assembly

 PERFORMANCE ORDER

  1. Establish a spring of the control valve, the valve and a connector in the pump case.
  1. The special tool 09222-32100 establish oil consolidation in the pump case.
  1. Softly insert assembly of a shaft and establish the rasporny plug and a lock ring.
  1. Establish a pump pulley with a segment shponka.
  1. Establish a spring and an internal sealing ring.
  1. Establish an external sealing ring in a lateral plate and establish a forward lateral plate.
  1. Insert pins into deepenings of the forward case, then establish a statorny ring, paying attention to the direction of its installation.
  1. Establish a rotor so that labels on a rotor settled down from outside, an opposite forward part of the case.
  1. Establish blades the rounded-off parts outside.
  1. Establish laying and a pump cover.
  2. Establish soaking-up pipe and a sealing ring.

Installation

 PERFORMANCE ORDER

  1. Establish the pump on an arm, put on a driving belt pulleys and tighten a bolt of adjustment of a tension of a belt. Inhaling moment: 3,5–10 N • m.
  1. Establish soaking-up filter.
  2. Connect to the pump a pressure head hose.

Establish a pressure head hose so that it was not overwound and did not make contact with any other parts.

  1. Fill in liquid. The recommended liquid: PSF–3.
  2. Pump over a hydraulic drive of the amplifier of a steering.
  3. Check the pressure created by the pump.