Elantr's Hyundai
+ Petrol engines 1,6, 1,8 and 2,0 of l
+ Diesel engine of 2,0 l
+ greasing System
+ cooling System
+ Fuel system
+ Monitoring systems and decrease in toxicity of the fulfilled gases
+ ignition System
+ System of preliminary heating of the diesel engine
+ Coupling
+ Mechanical transmission
+ Automatic transmission
+ Power shafts, forward and back axes
+ Suspension bracket
+ Steering
+ Brake system
+ Body
- Air central air
Specifications
Instruction on coolant application
Remarks at replacement of elements of central air of air
Connection of elements of central air of air
Precautionary measures
Installation of manometers for pressure measurement
Discharge of central air of air
Pumping of atmospheric air from central air
Connection of the final valve to a cylinder with a coolant
Charging of central air of air
Verification of operational characteristics
Oil for greasing of the compressor of the conditioner
Check and adjustment of a tension of poliklinovy belts
Conditioner compressor
Plug of coupling and pulley of the compressor of the conditioner
Coil of initiation of coupling
Check of a gap of coupling
Fan, condenser and relay
Dryer receiver
Sensor of threefold (double) pressure
Heating and ventilation block
Fan
Air filter
Drive of a zaslonka of supply of fresh / retsirkuliruyemy air
Check of the engine of the fan
Relay check
+ Electric equipment
Electric circuits
|
Heating and ventilation block
Removal
|
|
Disconnect a wire from the negative plug of the storage battery.
|
|
Disconnect from forward seats electric sockets and remove sitting.
|
|
|
|
|
At removal of forward seats do not damage an upholstery of salon of the car.
|
|
After removal of the handle from the gear shifting lever, an edge of a flat screw-driver remove the top cover of the console.
|
|
Turn out screws and remove the floor console.
|
|
|
Remove lateral covers from the floor console.
|
|
|
Remove a safety cushion of the driver.
|
|
|
For removal of a safety cushion look the corresponding description. |
|
|
Turn out screws of fastening of the bottom casing of a steering column and remove it.
|
|
|
Remove a spiral spring of a safety cushion of the driver.
|
|
|
Disconnect the socket and remove the multipurpose switch.
|
|
|
Turn out screws of fastening of a combination of devices.
|
|
|
Remove an ashtray, then turn out screws of fastening of a combination of devices and remove it.
|
Disconnect sockets from a combination of devices.
|
|
Remove a combination of devices.
|
|
|
Remove a radio receiver and the control panel the conditioner.
|
|
|
Turn out screws of fastening of the bottom decorative panel located under the dashboard.
|
|
|
Turn out screws of fastening of the lateral decorative panel and remove it from the dashboard.
|
|
|
Remove an arm of support of the dashboard from the driver.
|
|
|
Turn out bolts of fastening of a steering column and remove it.
|
|
|
Remove an upholstery from a forward door and the bottom furnish of a forward rack.
|
|
|
Disconnect sockets from the dashboard.
|
|
|
Remove a lattice of a heater and turn out bolts of fastening of the dashboard.
|
Remove lateral covers from the lower part of the dashboard and turn out bolts of fastening of the dashboard.
|
|
Turn out bolts of fastening of the dashboard to the central arm and a ware box.
|
|
|
Turn out other bolts of fastening of the dashboard.
|
Turn out a nut of fastening of the evaporator.
Remove the evaporator block.
Turn out nuts of fastening of a forward cross-piece of a motor compartment and remove it.
Turn out nuts of fastening of a heater.
Remove the heater block.
|
|
Installation
Installation is carried out to sequences, return to removal, taking into account reliable connection of all sockets.
|
|