Hyundai Elantra

since 2000-2004 of release

Repair and car operation



Elantr's Hyundai
+ Petrol engines 1,6, 1,8 and 2,0 of l
+ Diesel engine of 2,0 l
+ greasing System
+ cooling System
+ Fuel system
+ Monitoring systems and decrease in toxicity of the fulfilled gases
+ ignition System
+ System of preliminary heating of the diesel engine
+ Coupling
+ Mechanical transmission
+ Automatic transmission
+ Power shafts, forward and back axes
- Suspension bracket
   Specifications
   Rack of a forward suspension bracket
   Bottom lever of a forward suspension bracket
   Forward stabilizer of cross-section stability
   Rack of a back suspension bracket
   Cross-section levers of a back suspension bracket
   Longitudinal levers of a back suspension bracket
   Back stabilizer of cross-section stability
   Corners of installation of forward wheels
   Wear of tires
   Shift of wheels
   Check of withdrawal and course instability of the car
   Wheel palpation
   Tightening of nuts of fastening of a wheel
   Search and elimination of malfunctions
   Diagnostics of wear of tires
+ Steering
+ Brake system
+ Body
+ air Central air
+ Electric equipment
Electric circuits



Rack of a back suspension bracket

Removal

 PERFORMANCE ORDER

  1. Combine back sitting.
  1. Turn out three nuts of the top fastening of a back rack.
  1. Remove a back wheel.
  2. Disconnect from a back rack a brake tube and the sensor of frequency of rotation of a wheel.
  3. Disconnect draft of the stabilizer of cross-section stability.
  1. Unscrew nuts and get bolts of fastening of a rack to a fixing element of a back axis.

Be careful not to damage a rack of a back suspension bracket.

  1. Get a rack from under a car wing.

Dismantling

 PERFORMANCE ORDER

  1. Special J38402 adaptations, – 20 and – 50 compress a spring of a rack of a back suspension bracket.

For compression of a spring use only the reliable tool.

  1. Unscrew самоконтрящуюся a nut in the top part of a rod of the shock-absorber.
  2. Remove a rack support, a cylindrical spring and a dustproof cover.

Check

 PERFORMANCE ORDER

  1. Check a rack support on lack of wear or damages.
  2. Check rubber details on absence of damages or deterioration of their condition.
  3. Check a cylindrical spring on lack of a deflection and elasticity loss.
  1. Check the shock-absorber on existence abnormal resistance or extraneous noise (see. Rack of a forward suspension bracket).

Assembly

 PERFORMANCE ORDER

  1. Establish the bottom support of a spring so that its ledges entered into openings of a plate of a spring.
  2. Establish on the shock-absorber a dustproof cover.
  3. Special J38402 adaptations,–20 and–50 compress a cylindrical spring of a rack of a back suspension bracket.
  4. After complete compression of a spring establish it on the shock-absorber.

Combine a D-shaped opening in the top support of a spring with lysky on a shock-absorber rod.

  1. Correctly arrange the top and bottom ends of a cylindrical spring, having established them in dredging, and screw самоконтрящуюся a nut, but do not tighten it finally.

At assembly it is necessary to use new самоконтрящуюся a nut.

  1. Arrange a bolt of fastening of a support of a spring so that to combine a projection of laying, as is shown in drawing.

The identification label of a spring should settle down from below.

  1. Remove J38402 adaptations,–20 and–40 for spring compression.
  2. Tighten самоконтрящуюся a nut the demanded moment of an inhaling. Inhaling moment: 40–55 Nanometers.

Installation

Installation is carried out to sequences, return to removal.

After installation check corners of installation of back wheels.