Elantr's Hyundai
+ Petrol engines 1,6, 1,8 and 2,0 of l
+ Diesel engine of 2,0 l
+ greasing System
+ cooling System
+ Fuel system
+ Monitoring systems and decrease in toxicity of the fulfilled gases
+ ignition System
+ System of preliminary heating of the diesel engine
+ Coupling
+ Mechanical transmission
+ Automatic transmission
- Power shafts, forward and back axes
Specifications
Power shaft
Power shaft with CV JOINTS of ball type and type Birfield
Power shaft with Birfield CV JOINTS (B. J.) and tripoidny type (T. J.)
Rotary fist and nave of a forward wheel
Back axis/nave of a back wheel
Search and elimination of malfunctions
+ Suspension bracket
+ Steering
+ Brake system
+ Body
+ air Central air
+ Electric equipment
Electric circuits
|
Rotary fist and nave of a forward wheel
Removal
|
|
Before removal of power shafts close towels all sharp sides about power shafts that will provide protection of covers against damages. At removal of a power shaft be careful not to stretch the hinge of equal angular speeds as thus there can be a separation of internal elements of the hinge and to its possible damage. The CV JOINT and a protective cover should be reliably protected at works with power shafts or about them. |
|
|
Remove шплинт, unscrew a koronchaty nut and remove a washer of fastening of a power shaft to a nave of a forward wheel.
|
|
Take шплинт and unscrew a nut of fastening of a pin of the spherical hinge of a tip of steering bent for to a rotary fist. A stripper 09568–34000 squeeze out a pin of the spherical hinge from a rotary fist.
|
|
|
Cord fix a stripper for the closest element of the car. |
|
|
Remove a support and a soft wire fix it on a forward rack.
|
By the indicator of hour type measure palpation and an axial gap of a nave of a forward wheel.
|
|
Stripper 09568–34000 disconnect the spherical hinge of the bottom lever from a rotary fist.
|
|
|
Remove the sensor of frequency of rotation from a rotary fist.
|
Note situation and turn out bolts of fastening of the lower part of a rack of a forward suspension bracket to a rotary fist.
Kapron hammer beat out a power shaft from a nave of a forward wheel. If the power shaft densely sits in a nave of a forward wheel, spray propitochny aerosol solvent on area шлицов and then repeatedly screw a nut with a fillet so that it settled down flush with a shaft end face. Striking on a nut with a brass hammer, beat out a power shaft from a nave.
Remove a rotary fist together with a nave of a forward wheel.
|
|
Dismantling
|
|
|
|
Turn out two screws and remove a brake disk from a nave of a forward wheel.
|
|
|
Remove a lock spring ring.
|
|
|
Establish special tools 09517-29000, 09517-21500, as is shown in drawing.
|
Turning the special tool, remove a nave of a forward wheel from a rotary fist.
Remove the special tool and a dustproof ring.
|
|
The special tool 09495-33000, 09551-31000 remove an internal ring of the bearing from a nave.
|
|
|
The special tool 09495-33100, 09517-29000 remove an external ring of the bearing from a rotary fist.
|
|
|
Check
|
|
Check a nave on lack of cracks and wear.
Check a brake disk on absence of development and damages.
Check a rotary fist on lack of cracks.
Check the bearing on lack of cracks or damages.
|
|
Assembly
|
|
Apply a thin film konsistentny greasing in an opening of a rotary fist and on an external ring of the bearing.
|
|
Press with an opravka 09495–33100 corresponding diameter press the new bearing of a wheel.
|
|
|
Do not make effort of a press an internal ring of the bearing.
- At installation always use the new bearing.
|
Establish a spring ring in a groove of a rotary fist.
Establish a dustproof ring.
|
|
Press with an opravka 09495–33100 corresponding diameter press a nave in the wheel bearing.
|
|
|
Do not make effort of a press an external ring of the bearing. |
Establish a brake board.
|
|
The special tool 09517-21500 tighten a nave to a rotary fist, having tightened an adaptation bolt the moment of 200-260 N • m.
|
Several times turn a nave that elements of the bearing were established on the places.
|
|
Measure a torque which is necessary for putting for a bearing provorachivaniye. Torque: no more than 1,8 N • m.
|
If a torque of 0 N • m, measure axial люфт the nave bearing.
|
|
If the torque exceeds demanded value, means, the bearing is incorrectly established in a rotary fist and on a nave. Disassemble a rotary fist and repeatedly bring together him. Axial люфт bearing: no more than 0,008 mm.
|
Remove the special tool 09517-21500.
Establish a brake disk and fix it screws.
|
|
Installation
|
|
Installation is carried out to sequences, return to removal.
|
|
Tighten carving connections by the demanded moments in the following order:
Nut of fastening of a power shaft: 200–260 N • m
Nut of fastening of a pin of the spherical hinge of the bottom lever to a rotary fist: 60–72 N • m
Nut of fastening of a rotary fist to stoyke:130-150 N • m
|
Establish a rack and a power shaft in a rotary fist.
Connect the ABS sensor.
Establish a support.
Tighten a nut of fastening of a pin of the spherical hinge of the bottom lever to a rotary fist.
Tighten a nut of fastening of a pin of the spherical hinge of a tip of steering bent for to a rotary fist and fix it a pin.
Establish a washer and tighten a koronchaty nut.
Establish a wheel.
|
|
|
|