Elantr's Hyundai
+ Petrol engines 1,6, 1,8 and 2,0 of l
+ Diesel engine of 2,0 l
+ greasing System
+ cooling System
+ Fuel system
+ Monitoring systems and decrease in toxicity of the fulfilled gases
+ ignition System
+ System of preliminary heating of the diesel engine
+ Coupling
+ Mechanical transmission
+ Automatic transmission
+ Power shafts, forward and back axes
+ Suspension bracket
+ Steering
+ Brake system
- Body
Specifications
Adjustment of hinges of a cowl
Trunk lid
Door of a luggage compartment
Forward door
Back door
Moldings
Roof hatch
Console
Dashboard
Ceiling furnish
Internal upholstery of salon
Front bumper
Rear bumper
Sitting lobbies
Back seat
Seat belts
Humeral seat belt of back sitting
Zone seat belt of back sitting
Search and elimination of malfunctions
+ air Central air
+ Electric equipment
Electric circuits
|
Roof hatch
Removal
|
|
Before removal of the hatch remove the following elements:
– a lamp from the top console;
– sun-protection peaks and internal rear-view mirror;
– upholstery of a forward rack.
|
|
Remove the decorative panel and the glass panel of the hatch. Inhaling moment: 4–6 N • m.
|
|
|
Disconnect a drainage hose.
|
|
|
Turn out bolts and nuts and remove the hatch assembled.
Inhaling moment:
Assembly bolts of the hatch: 7–11 N • m
Assembly nuts of the hatch: 4–6 N • m
|
|
|
|
|
At hatch removal assembled be careful not to damage adjacent elements of the car. |
Dismantling
|
|
|
|
Remove a sun-protection shtorka.
|
|
|
Remove knot of the directing.
|
Remove the drive block with the electric motor.
|
|
|
|
|
|
At engine removal the knot ползуна should be in completely closed position. If there is a discrepancy between the glass panel and an engine ring in completely closed position, the hatch will not function privilno. |
|
Installation
Installation is carried out to sequences, return to removal.
|
|
|
|
Check that trailer switches of the engine (and LS2) are completely closed by LS1. Establish the center of a directing roller and a label ползуна in completely closed position. |
|
Functioning check after installation
If the hatch moves slowly, execute the following adjustments and checks.
|
|
Be convinced that the storage battery is completely charged.
Be convinced that in knot ползуна there are no abrasive materials.
Be convinced that when opening the glass panel of the hatch, the back part of the panel does not cling to the roof panel. In the presence of a gap, completely open the glass panel and move a stopper.
|
|
If a stopper will advance too far, it can lead to failures in work and leaks. Be convinced that a gap between the glass panel and the panel of a roof no more than 0,3 mm. |
|
|
Measure effort of the block of a drive of the hatch and, rotating a nut of adjustment of a torque on the drive block, adjust it to 15–25 kg.
|
|
|
After adjustment be convinced that blocked a nut a washer with a clamp.
|
|
|
Adjustment
|
|
Adjust height of installation of the glass panel of the hatch in relation to the roof panel.
Forward party: 0 (+0,–1,0) mm
Back party: 0 (+1, +0) mm
|
If the height of installation of the glass panel of the hatch in relation to the panel of a roof does not correspond demanded, adjust it as follows.
|
|
|
|
Weaken forward and back screws. Adjust height of installation of the glass panel of the hatch in relation to the roof panel.
|
|
|
Weaken nuts of fastening of the glass panel and adjust a gap between the glass panel and the roof panel.
|
|
|
|
|